The first cool snap in Savannah sends a lot of pool owners out to the equipment pad to fire up a heater that hasn't run since spring. Some of those heaters don't start. Before you book a repair, a short checklist will tell you whether it's a setting you can fix in minutes or a part that needs a technician.
This guide covers gas heaters and heat pumps, the problems we see most often around Savannah, Richmond Hill and Pooler, and the signs that mean you should stop troubleshooting.
Safety first
If you smell gas near the heater, turn it off, stay away from open flames and call your gas utility or propane company. And don't jumper or bypass a safety switch to force the heater on. Those switches protect the heat exchanger and your home.
Quick checks you can do yourself
Is the heater actually being told to heat?
Start with the simple stuff, because it solves more calls than anything else:
- The heater's display is on and set to pool or spa, not off.
- The target temperature is above the water temperature.
- If you have automation (a panel or a phone app), the heater is enabled there too. Power blips and app updates can quietly switch it off.
Is water moving through it?
A pool heater won't fire unless it senses enough flow. Check your filter pressure, empty the pump and skimmer baskets, and make sure no valves are half closed. Oak leaves and pine straw fill baskets quickly in the fall.
If you've switched to a variable-speed pump, look at its schedule. The slow, energy-saving speed often isn't enough flow for the heater. The pump needs to run at a higher speed whenever the heater is on.
Is there fuel?
Natural gas customers: confirm the gas valve at the heater is open. Propane customers: check the tank gauge. A tank running low can light the burner and then lose the flame.
Problems that usually need a technician
Ignition faults
A heater that clicks, runs its fan, then shuts down with an ignition error usually needs its igniter or flame sensor cleaned or replaced. After a few failed tries, most heaters lock out on purpose.
Pests in the cabinet
Fire ants are a real problem in Chatham and Bryan counties. They nest in warm control boards and short them out. Mud daubers, lizards and mice also move into burner trays and vents over the summer. If you open the access panel and find a nest, have it cleaned out and inspected before running the heater.
Corrosion
Humidity, salt air near the marsh and chlorine fumes from chemicals stored next to the equipment all eat at wiring and circuit boards. A connection that was marginal in spring can fail on the first cold night.
Safety switches that keep tripping
A high-limit or rollout switch that trips points to an underlying problem such as low flow, scale buildup or a venting issue. Resetting it without finding the cause just sets up the next failure.
Heat pump not keeping up
Heat pumps pull warmth from outdoor air. Below about 50°F they slow down a lot and may spend time defrosting. A heat pump that runs but heats slowly in December may be normal. One with no display, no fan or an error code needs a diagnosis.
Signs to stop and call
- The same error comes back after you've checked settings, flow and fuel
- Soot, scorch marks, melted wires or water dripping inside the cabinet
- The heater cycles on and off over and over
- Any gas smell (call the gas company first)
- A heater past 8 to 10 years old that needs a major part, where replacement may cost less over time
Pool heater repair in Savannah and Richmond Hill
Perfect Pools diagnoses and repairs gas pool heaters and heat pumps across Savannah, Richmond Hill, Pooler, Wilmington Island, Skidaway Island, Rincon and Bluffton. Our technicians will tell you straight whether a repair is worth it or a replacement makes more sense.
Call Perfect Pools:
- Richmond Hill: (912) 459-0160
- Savannah / Garden City: (912) 303-7372
Weekly maintenance customers can simply mention the heater to their technician on the next visit.
Common questions
My heater starts and then shuts off. What's wrong?
Most often it's low flow from a dirty filter, full baskets or a variable-speed pump running too slowly. A weak propane supply or a worn igniter can do the same thing.
How cold is too cold for a heat pump?
Most pool heat pumps lose a lot of output once the air drops below about 50°F. For swimming into December, a gas heater or a heater-plus-cover combination works better.
Is it safe to reset the heater myself?
Turning it off and on and checking settings, flow and fuel is fine. Leave safety switches, gas valves and the control board to a technician.
How long do pool heaters last around Savannah?
Roughly 7 to 10 years for a gas heater or heat pump. Humidity, pests, salt air and unbalanced water shorten that.
When should I have my heater serviced?
Ahead of the season you plan to use it: late summer for fall swimming and late winter for spring. That's when the schedule is most open.